fix ehex command

Syntax

fix ID group-ID ehex nevery F keyword value
  • ID, group-ID are documented in fix command

  • ehex = style name of this fix command

  • nevery = add/subtract heat every this many timesteps

  • F = energy flux into the reservoir (energy/time units)

  • zero or more keyword/value pairs may be appended to args

  • keyword = region or constrain or com or hex

    region value = region-ID
      region-ID = ID of region (reservoir) atoms must be in for added thermostatting force
    constrain value = none
      apply the constraint algorithm (SHAKE or RATTLE) again at the end of the timestep
    com value = none
      rescale all sites of a constrained cluster of atom if its COM is in the reservoir
    hex value = none
      omit the coordinate correction to recover the HEX algorithm

Examples

# Lennard-Jones, from examples/in.ehex.lj

fix fnve all nve
# specify regions rhot and rcold
...
fix fhot all ehex 1 0.15 region rhot
fix fcold all ehex 1 -0.15 region rcold

# SPC/E water, from examples/in.ehex.spce
fix fnve all nve
# specify regions rhot and rcold
...
fix fhot all ehex 1 0.075 region rhot constrain com
fix fcold all ehex 1 -0.075 region rcold constrain com
fix frattle all rattle 1e-10 400 0 b 1 a 1

Description

This fix implements the asymmetric version of the enhanced heat exchange algorithm (Wirnsberger). The eHEX algorithm is an extension of the heat exchange algorithm (Ikeshoji) and adds an additional coordinate integration to account for higher-order truncation terms in the operator splitting. The original HEX algorithm (implemented as fix heat) is known to exhibit a slight energy drift limiting the accessible simulation times to a few nanoseconds. This issue is greatly improved by the new algorithm decreasing the energy drift by at least a factor of a hundred (LJ and SPC/E water) with little computational overhead.

In both algorithms (non-translational) kinetic energy is constantly swapped between regions (reservoirs) to impose a heat flux onto the system. The equations of motion are therefore modified if a particle \(i\) is located inside a reservoir \(\Gamma_k\) where \(k>0\). We use \(\Gamma_0\) to label those parts of the simulation box which are not thermostatted.) The input parameter region-ID of this fix corresponds to \(k\). The energy swap is modelled by introducing an additional thermostatting force to the equations of motion, such that the time evolution of coordinates and momenta of particle \(i\) becomes (Wirnsberger)

\[\begin{split}\dot{\mathbf r}_i &= \mathbf v_i, \\ \dot{\mathbf v}_i &= \frac{\mathbf f_i}{m_i} + \frac{\mathbf g_i}{m_i}.\end{split}\]

The thermostatting force is given by

\[\begin{split}\mathbf g_i = \begin{cases} \frac{m_i}{2} \frac{ F_{\Gamma_{k(\mathbf r_i)}}}{ K_{\Gamma_{k(\mathbf r_i)}}} \left(\mathbf v_i - \mathbf v_{\Gamma_{k(\mathbf r_i)}} \right) & \mbox{$k(\mathbf r_i)> 0$ (inside a reservoir),} \\ 0 & \mbox{otherwise, } \end{cases}\end{split}\]

where \(m_i\) is the mass and \(k(\mathbf r_i)\) maps the particle position to the respective reservoir. The quantity \(F_{\Gamma_{k(\mathbf r_i)}}\) corresponds to the input parameter F, which is the energy flux into the reservoir. Furthermore, \(K_{\Gamma_{k(\mathbf r_i)}}\) and \(v_{\Gamma_{k(\mathbf r_i)}}\) denote the non-translational kinetic energy and the center of mass velocity of that reservoir. The thermostatting force does not affect the center of mass velocities of the individual reservoirs and the entire simulation box. A derivation of the equations and details on the numerical implementation with velocity Verlet in LAMMPS can be found in reference “(Wirnsberger)”#_Wirnsberger.

Note

This fix only integrates the thermostatting force and must be combined with another integrator, such as fix nve, to solve the full equations of motion.

This fix is different from a thermostat such as fix nvt or fix temp/rescale in that energy is added/subtracted continually. Thus if there is not another mechanism in place to counterbalance this effect, the entire system will heat or cool continuously.

Note

If heat is subtracted from the system too aggressively so that the group’s kinetic energy would go to zero, then LAMMPS will halt with an error message. Increasing the value of nevery means that heat is added/subtracted less frequently but in larger portions. The resulting temperature profile will therefore be the same.

This fix will default to fix_heat (HEX algorithm) if the keyword hex is specified.


Compatibility with SHAKE and RATTLE (rigid molecules):

This fix is compatible with fix shake and fix rattle. If either of these constraining algorithms is specified in the input script and the keyword constrain is set, the bond distances will be corrected a second time at the end of the integration step. It is recommended to specify the keyword com in addition to the keyword constrain. With this option all sites of a constrained cluster are rescaled, if its center of mass is located inside the region. Rescaling all sites of a cluster by the same factor does not introduce any velocity components along fixed bonds. No rescaling takes place if the center of mass lies outside the region.

Note

You can only use the keyword com along with constrain.

To achieve the highest accuracy it is recommended to use fix rattle with the keywords constrain and com as shown in the second example. Only if RATTLE is employed, the velocity constraints will be satisfied.

Note

Even if RATTLE is used and the keywords com and constrain are both set, the coordinate constraints will not necessarily be satisfied up to the target precision. The velocity constraints are satisfied as long as all sites of a cluster are rescaled (keyword com) and the cluster does not span adjacent reservoirs. The current implementation of the eHEX algorithm introduces a small error in the bond distances, which goes to zero with order three in the timestep. For example, in a simulation of SPC/E water with a timestep of 2 fs the maximum relative error in the bond distances was found to be on the order of \(10^{-7}\) for relatively large temperature gradients. A higher precision can be achieved by decreasing the timestep.


Restart, fix_modify, output, run start/stop, minimize info

No information about this fix is written to binary restart files. None of the fix_modify options are relevant to this fix.

No parameter of this fix can be used with the start/stop keywords of the run command. This fix is not invoked during energy minimization.

Restrictions

This fix is part of the RIGID package. It is only enabled if LAMMPS was built with that package. See the Build package page for more info.

Default

none


(Ikeshoji) Ikeshoji and Hafskjold, Molecular Physics, 81, 251-261 (1994).

(Wirnsberger) Wirnsberger, Frenkel, and Dellago, J Chem Phys, 143, 124104 (2015).